gated OSPF protocol statement

   ospf yes|no|on|off [ {
       [ defaults {
           preference preference ;
           cost cost ;
           tag [tag | as [as_tag]] ;
           type 1|2 ;
       } ] ;
       [exportlimit routes ;]
       [exportinterval time ;]
       [traceoptions traceoptions ;]
       [monitorauthkey authkey ;]
       [area area {
           authtype 0|1|none|simple ;
           stub [cost cost];
           networks {
               network [mask mask] ;
           } ;
           stubhosts {
               host cost cost ;
           } ;
           interface interface [cost cost] {
               [enable|disable] ;
               retransmitinterval time ;
               transitdelay time ;
               priority priority ;
               hellointerval time ;
               routerdeadinterval time ;
               authkey auth_key ;
           } ;
           interface interface nonbroadcast [cost cost] {
               pollinterval time ;
               routers {
                   gateway [eligible] ;
                   . . .
               } ;
               [enable|disable] ;
               retransmitinterval time ;
               transitdelay time ;
               priority priority ;
               hellointerval time ;
               routerdeadinterval time ;
               authkey auth_key ;
           } ;
       } ; ]
       [ backbone {
           authtype 0|1|none|simple ;
           networks {
               network [mask mask] ;
           } ;
           stubhosts {
               host cost cost ;
           } ;
           interface interface [cost cost] {
               [enable|disable] ;
               retransmitinterval time ;
               transitdelay time ;
               priority priority ;
               hellointerval time ;
               routerdeadinterval time ;
               authkey auth_key ;
           } ;
           . . .
           interface interface nonbroadcast [cost cost] {
               pollinterval time ;
               routers {
                   gateway [eligible] ;
                   . . .
               } ;
               [enable|disable] ;
               retransmitinterval time ;
               transitdelay time ;
               priority priority ;
               hellointerval time ;
               routerdeadinterval time ;
               authkey auth_key ;
           } ;
           . . .
           virtuallink neighborid host transitarea area {
               [enable|disable] ;
               retransmitinterval time ;
               transitdelay time ;
               priority priority ;
               hellointerval time ;
               routerdeadinterval time ;
               authkey auth_key ;
           } ;
           . . .
       } ; ]
   } ] ;

defaults

These parameters specify the defaults used when importing OSPF ASE routes into the gated routing table and exporting routes
from the gated routing table into OSPF ASEs. The following paragraphs define each statement.

preference preference

The preference is used to determine how OSPF routes compete with
routes from other protocols in the gated routing table. The default value is 150.

cost cost

The cost is used when exporting a non-OSPF
route from the gated routing table into OSPF as an ASE. The default value is 1. This may be explicitly overridden in export policy.

tag [ as ] tag

OSPF ASE routes have a 32-bit tag field that is not used by the OSPF protocol but may be used by export policy to
filter routes. When OSPF is interacting with an egp, the tag field may be used to propagate AS path information, in which case the as keyword is specified that the tag is limited to 12 bits of information. If not specified, the tag is set to zero.

type 1 | 2

Routes exported from the gated routing table into OSPF default to becoming type 1 ASEs. This default may be explicitly changed here and
overridden in export policy.

ASE export rate

Because of the nature of OSPF, the rate at which ASEs
are flooded must be limited. These two parameters can be used to adjust those rate limits.

exportinterval time

This specifies how often a batch of ASE link-state advertisements
will be generated and flooded into OSPF. The default is once per second.

exportlimit routes

This parameter specifies how many ASEs will be generated and
flooded in each batch. The default is 100.

traceoptions traceoptions

Specifies the tracing options for OSPF. (See
``gated trace statements'').

monitorauthkey authkey

OSPF state may be queried using the ospf_monitor utility (see
ospf_monitor(ADMN). This utility sends nonstandard OSPF packets that generate a text response from OSPF. By default, these requests are not authenticated. If an authentication key is configured, the incoming requests must match the specified authentication key. No OSPF state may be changed by these packets, but the act of querying OSPF can utilize system resources.

backbone area area

Each OSPF router must be configured into at least one
OSPF area. If more than one area is configured, at least one must be the backbone. The backbone may only be configured using the backbone keyword; it may not be specified as area 0. The backbone interface may be a ``virtuallink''.

authtype 0 | 1 | none | simple

OSPF specifies an authentication scheme per area. Each interface
in the area must use this same authentication scheme, although it may use a different authentication key. The currently valid values are none (0) for no authentication, or simple (1) for simple password authentication.

stub [ cost cost]

A stub area is one in which there are no ASE routes. If a cost is
specified, this is used to inject a default route into the area with the specified cost.

networks

The networks list describes the scope of an area. Intra-area
LSAs that fall within the specified ranges are not advertised into other areas as inter-area routes. Instead, the specified ranges are advertised as summary network LSAs. Intra-area LSAs that do not fall into any range are also advertised as summary network LSAs. This option is very useful on well-designed networks in reducing the amount of routing information propagated between areas. The entries in this list are either networks or a subnetwork/mask pair. See ``gated route filtering'' for more detail about specifying ranges.

stubhosts

This list specifies directly attached hosts that should be
advertised as reachable from this router and the costs they should be advertised with. Point-to-point interfaces on which it is not desirable to run OSPF should be specified here.

It is also useful to assign an additional address to the loopback interface (one not on the 127 network) and advertise it as a stubhosts. If this address is the same one used as the router-id, it enables routing to OSPF routers by router-id instead of by interface address. This is more reliable than routing to one of the router interface addresses that may not always be reachable.

interface interface_list [cost cost ]

This form of the interface clause is used to configure a broadcast
(which requires IP multicast support) or a point-to-point interface. See ``gated interfaces statements'' for the description of the interface_list.

Each interface has a cost. The costs of all interfaces a packet must cross to reach a destination are summed to get the cost to that destination. The default cost is one, but another nonzero value may be specified.

Interface parameters common to all types of interface are:

retransmitinterval time

The number of seconds between link-state advertisement
retransmissions for adjacencies belonging to this interface.

transitdelay time

The estimated number of seconds required to transmit a link-state
update over this interface. Transitdelay takes into account transmission and propagation delays and must be greater than 0.

priority priority

A number between 0 and 255 specifying the priority for
becoming the designated router on this interface. When two routers attached to a network both attempt to become the designated router, the one with the higher priority wins. A router whose router priority is set to 0 is ineligible to become designated router.

hellointerval time

The length of time, in seconds, between Hello packets that the
router sends on the interface.

routerdeadinterval time

The number of seconds of not hearing a router's Hello packets
before the router's neighbors will declare it down.

authkey auth_key

Used by OSPF authentication to generate and verify the
authentication field in the OSPF header. The authentication key can be configured on a per-interface basis. It is specified by one to eight decimal digits separated by periods, a one to eight byte hexadecimal string preceded by 0x, or a one to eight character string in double quotes.

interface interface_list nonbroadcast [ cost cost ]

This form of the interface clause is used to specify a nonbroadcast
interface on a nonbroadcast multiaccess (NBMA) media. Since an OSPF broadcast media must support IP multicasting, a broadcast capable media, such as Ethernet, that does not support IP multicasting must be configured as a nonbroadcast interface.

A nonbroadcast interface supports any of the standard interface clauses listed above, plus the following two that are specific to nonbroadcast interfaces:

pollinterval time

Before adjacency is established with a neighbor, OSPF packets
are sent periodically at the specified time.

routers

By definition, it is not possible to send broadcast packets to
discover OSPF neighbors on a nonbroadcast, so all neighbors must be configured. The list includes one or more neighbors and an indication of their eligibility to become a designated router.

virtuallink neighborid host transitarea area

Virtual links are used to establish or increase connectivity of the
backbone area. host is the router-id of the other end of the virtual link. The transit area specified must also be configured on this system. All standard interface parameters defined by the interface clause above may be specified on a virtual link.

Home Notes Home MCSE MCSE MCITP + Security CCNA MCITP 2008  Boot Camp Schedule Register Frequently Asked Questions Course Fees Contact US Boot Camp Location Compare us to our competitors Testimonials Sitemap   Testimonials  Join MCSE MCITP Boot Camp & CCNA Boot Camp Back to Back Certification Today. links  270  290    291  293    294  298  299   Security  640-801  routing 811  821   831  Resources MCSE MCITP + CCNA  Training  Card pay  Papal  MCSE MCITP Notes  CCNA Notes    index main   root   link  resources home    Ref1 Ref2

Vibrant offers MCSE certification training boot camp for $5400 all inclusive, instructor led at California and Baltimore.

Vibrant Bootcamp Participants come from All Around the World. Vibrant has trained students from more than 15 countries like USA, UK, (Scotland, Ireland, Wales), Switzerland, Germany, Australia, Canada, France, Holland, Japan, Belgium, Bahrain, New Zealand, Tanzania, Turkey, Kenya and more.