	Home

	MCSE

	MCSE + Security

	CCNA

	CCNP

	Schedule

	Register

	Frequently Asked Questions

	Course Fees

	Contact US

	Boot Camp Location

	Compare us to our competitors

	Testimonials

	Sitemap

JOIN THE BEST MCITP Boot Camp, MCSE Boot Camp also CCNA , CCNP Certification Boot Camp Training program. 100% Guaranteed - Lowest Fees, Highest Passing Rate. MCSE Boot Camp Certification

MCITP MCSE and CCNA Certification Notes Series :

MCSE 2016 Boot Camp : Azure Boot camp : CCNA / CCNAX Boot Camp:

CCNA Boot Camp

Cisco Hierarchical Model:
For more information about this, please read our separate tutorial titled "The Cisco Hierarchical Model".

OSI Model:
The OSI model is a layered model and a conceptual standard used for defining standards to promote multi-vendor integration as well as maintain constant interfaces and isolate changes of implementation to a single layer. It is NOT application or protocol specific. In order to pass any Cisco exam, you need to know the OSI model inside and out.

The OSI Model consists of 7 layers as follows:

Layer	Description	Device	Protocol
Application	Provides network access for applications, flow control and error recovery. Provides communications services to applications by identifying and establishing the availability of other computers as well as to determine if sufficient resources exist for communication purposes.	Gateway	NCP, SMB, SMTP, FTP, SNMP, Telnet, Appletalk
Presentation	Performs protocol conversion, encryption and data compression	Gateway and redirectors	NCP, AFP, TDI
Session	Allows 2 applications to communicate over a network by opening a session and synchronizing the involved computers. Handles connection establishment, data transfer and connection release	Gateway	NetBios
Transport	Repackages messages into smaller formats, provides error free delivery and error handling functions	Gateway	NetBEUI, TCP, SPX, and NWLink
Network	Handles addressing, translates logical addresses and names to physical addresses, routing and traffic management.	Router and brouter	IP, IPX, NWLink, NetBEUI
**Data Link	Packages raw bits into frames making it transmitable across a network link and includes a cyclical redundancy check(CRC). It consists of the LLC sublayer and the MAC sublayer. The MAC sublayer is important to remember, as it is responsible for appending the MAC address of the next hop to the frame header. On the contrary, LLC sublayer uses Destination Service Access Points and Source Service Access Points to create links for the MAC sublayers.	Switch, bridge and brouter	None
Physical	Physical layer works with the physical media for transmitting and receiving data bits via certain encoding schemes. It also includes specifications for certain mechanical connection features, such as the adaptor connector.	Multiplexer and repeater	None

Here is an easy way to memorize the order of the layers:
All People Seem To Need Data Processing. The first letter of each word corresponds to the first letter of one of the layers. It is a little corny, but it works.

Class	Range	Explanation
A	1-126	IP addresses can be class A, B or C. Class A addresses are for networks with a large number of hosts. The first octet is the netid and the 3 remaining octets are the hostid. Class B addresses are used in medium to large networks with the first 2 octets making up the netid and the remaining 2 are the hostid. A class C is for smaller networks with the first 3 octets making up the netid and the last octet comprising the hostid. The later two classes aren’t used for networks.
B	128-191
C	192-223
D	224-239 (Multicasting)
E	240-255 (Experimental)

A subnet mask blocks out a portion of an IP address and is used to differentiate between the hostid and netid. The default subnet masks are as follows:

Class	Default Subnet	# of Subnets	# of Hosts Per Subnet
Class A	255.0.0.0	126	16,777,214
Class B	255.255.0.0	16,384	65,534
Class C	255.255.255.0	2,097,152	254

In these cases, the part of the IP address blocked out by 255 is the Net ID.

3COM’s IP addressing tutorial is just superior. It covers basic IP addressing options as well as subnetting and VLSM/CIDR.

IPX/SPX:
IPX will also be an important issue to consider in network management given the fact there many companies still use Netware servers. There are two parts to every IPX Network address - the Network ID and the Host ID. The first 8 hex digits represent the network ID, while the remaining hex digits represent the host ID, which is most likely the same as the MAC address, meaning we do not need to manually assign node addresses. Note that valid hexadecimal digits range from 0 through 9, and hexadecimal letters range from A through F. FFFFFFFF in hexadecimal notation = 4292967295 in decimal.

Sequenced Packet Exchange(SPX) belongs to the Transport layer, and is connection-oriented. It creates virtual circuits between hosts, and that each host is given a connection ID in the SPX header for identifying the connection. Service Advertisement Protocol(SAP) is used by NetWare servers to advertise network services via broadcast at an interval of every 60 minutes by default.

Logging to an External Server

Configuring the syslog Daemon on a UNIX syslog Server

Before you can send system log messages to a UNIX syslog server, you must configure the syslog daemon on the UNIX server. Log in as root, and perform these steps:

Step 1 Add a line such as the following to the file /etc/syslog.conf:

user.debug      /var/log/myfile.log

Note There must be five tab characters between user.debug and /var/log/myfile.log. Refer to entries in the /etc/syslog.conf file for further examples.

The switch sends messages according to specified facility types and severity levels. The user keyword specifies the UNIX logging facility used. The messages from the switch are generated by user processes. The debug keyword specifies the severity level of the condition being logged. You can set UNIX systems to receive all messages from the switch.

Step 2 Create the log file by entering these commands at the UNIX shell prompt:

   $ touch /var/log/myfile.log
   $ chmod 666 /var/log/myfile.log

Step 3 Make sure the syslog daemon reads the new changes by entering this command:

   $ kill -HUP \Qcat /etc/syslog.pid

Before you can send system log messages to a UNIX syslog server, you must configure the syslog daemon on the UNIX server.

Configuring syslog Servers

To configure the switch to log messages to a syslog server, perform these tasks in privileged mode:

Task Command

Step 1 Add a syslog server to the configuration¹. logging server ip_addr

Step 2 Enable system message logging to configured syslog servers. logging server enable

Step 3 Set the facility and severity level for syslog server messages. logging level facility severitydefault

¹You can configure a maximum of three syslog servers at any time.

To delete a syslog server from the configuration, enter the clear logging server command as follows:

   Switch1# clear logging server ip_address

To disable system message logging to configured syslog server, enter the set logging server command as follows:

   Switch1# set logging server disable

Call Now : 800-519- 2267

Why Vibrant Boot camp

No Prestudy

Longest Duration Bootcamp

Chalk Talk Training

Highest Passing Rate

Bootcamp since 1997

Guaranteed Lowest Rate

Guaranteed Certification ...

Testimonials

If you're serious about getting certified, this is the place to go. Definitely worth their competitive price. Excellent instructors, making it possible for anyone to learn no matter what your level of experience or knowledge.

Michael Doty

MCITP MCSE CCNA CCNP Boot Camp

Logging to an External Server