Application Laye - OSI layer - CCNA Exam Guide - Vibrant MCSE CCNA CCNP Boot Camps at USA, UK, India

	Home

	MCSE

	MCSE + Security

	CCNA

	CCNP

	Schedule

	Register

	Frequently Asked Questions

	Course Fees

	Contact US

	Boot Camp Location

	Compare us to our competitors

	Testimonials

	Sitemap

JOIN THE BEST MCITP Boot Camp, MCSE Boot Camp also CCNA , CCNP Certification Boot Camp Training program. 100% Guaranteed - Lowest Fees, Highest Passing Rate. MCSE Boot Camp Certification

MCITP MCSE and CCNA Certification Notes Series :

MCSE 2016 Boot Camp : Azure Boot camp : CCNA / CCNAX Boot Camp:

CCNA Boot Camp

Cisco Hierarchical Model:
For more information about this, please read our separate tutorial titled "The Cisco Hierarchical Model".

OSI Model:
The OSI model is a layered model and a conceptual standard used for defining standards to promote multi-vendor integration as well as maintain constant interfaces and isolate changes of implementation to a single layer. It is NOT application or protocol specific. In order to pass any Cisco exam, you need to know the OSI model inside and out.

The OSI Model consists of 7 layers as follows:

Layer	Description	Device	Protocol
Application	Provides network access for applications, flow control and error recovery. Provides communications services to applications by identifying and establishing the availability of other computers as well as to determine if sufficient resources exist for communication purposes.	Gateway	NCP, SMB, SMTP, FTP, SNMP, Telnet, Appletalk
Presentation	Performs protocol conversion, encryption and data compression	Gateway and redirectors	NCP, AFP, TDI
Session	Allows 2 applications to communicate over a network by opening a session and synchronizing the involved computers. Handles connection establishment, data transfer and connection release	Gateway	NetBios
Transport	Repackages messages into smaller formats, provides error free delivery and error handling functions	Gateway	NetBEUI, TCP, SPX, and NWLink
Network	Handles addressing, translates logical addresses and names to physical addresses, routing and traffic management.	Router and brouter	IP, IPX, NWLink, NetBEUI
**Data Link	Packages raw bits into frames making it transmitable across a network link and includes a cyclical redundancy check(CRC). It consists of the LLC sublayer and the MAC sublayer. The MAC sublayer is important to remember, as it is responsible for appending the MAC address of the next hop to the frame header. On the contrary, LLC sublayer uses Destination Service Access Points and Source Service Access Points to create links for the MAC sublayers.	Switch, bridge and brouter	None
Physical	Physical layer works with the physical media for transmitting and receiving data bits via certain encoding schemes. It also includes specifications for certain mechanical connection features, such as the adaptor connector.	Multiplexer and repeater	None

Here is an easy way to memorize the order of the layers:
All People Seem To Need Data Processing. The first letter of each word corresponds to the first letter of one of the layers. It is a little corny, but it works.

Class	Range	Explanation
A	1-126	IP addresses can be class A, B or C. Class A addresses are for networks with a large number of hosts. The first octet is the netid and the 3 remaining octets are the hostid. Class B addresses are used in medium to large networks with the first 2 octets making up the netid and the remaining 2 are the hostid. A class C is for smaller networks with the first 3 octets making up the netid and the last octet comprising the hostid. The later two classes aren’t used for networks.
B	128-191
C	192-223
D	224-239 (Multicasting)
E	240-255 (Experimental)

A subnet mask blocks out a portion of an IP address and is used to differentiate between the hostid and netid. The default subnet masks are as follows:

Class	Default Subnet	# of Subnets	# of Hosts Per Subnet
Class A	255.0.0.0	126	16,777,214
Class B	255.255.0.0	16,384	65,534
Class C	255.255.255.0	2,097,152	254

In these cases, the part of the IP address blocked out by 255 is the Net ID.

3COM’s IP addressing tutorial is just superior. It covers basic IP addressing options as well as subnetting and VLSM/CIDR.

IPX/SPX:
IPX will also be an important issue to consider in network management given the fact there many companies still use Netware servers. There are two parts to every IPX Network address - the Network ID and the Host ID. The first 8 hex digits represent the network ID, while the remaining hex digits represent the host ID, which is most likely the same as the MAC address, meaning we do not need to manually assign node addresses. Note that valid hexadecimal digits range from 0 through 9, and hexadecimal letters range from A through F. FFFFFFFF in hexadecimal notation = 4292967295 in decimal.

Sequenced Packet Exchange(SPX) belongs to the Transport layer, and is connection-oriented. It creates virtual circuits between hosts, and that each host is given a connection ID in the SPX header for identifying the connection. Service Advertisement Protocol(SAP) is used by NetWare servers to advertise network services via broadcast at an interval of every 60 minutes by default.

Application Layer

The application layer is the OSI layer closest to the end user, which means that both the OSI application layer and the user interact directly with the software application. This layer interacts with software applications that implement a communicating component. Such application programs fall outside the scope of the OSI model. Application-layer functions typically include identifying communication partners, determining resource availability, and synchronizing communication.

When identifying communication partners, the application layer determines the identity and availability of communication partners for an application with data to transmit. When determining resource availability, the application layer must decide whether sufficient network resources for the requested communication exist. In synchronizing communication, all communication between applications requires cooperation that is managed by the application layer.

Two key types of application-layer implementations are TCP/IP applications and OSI applications. TCP/IP applications are protocols, such as Telnet, File Transfer Protocol (FTP), and Simple Mail Transfer Protocol (SMTP), that exist in the Internet Protocol suite. OSI applications are protocols, such as File Transfer, Access, and Management (FTAM), Virtual Terminal Protocol (VTP), and Common Management Information Protocol (CMIP), that exist in the OSI suite.

Internetworking Applications

WWW

-Connects countless servers presenting diverse formats: multimedia, graphics, text, sound, and video. Applications such as Netscape Navigator, Internet Explorer, and Mosaic simplify accessing and viewing web sites.

EMAIL

-Versatile can use SMTP or X.400 to deliver messages between different email applications.

Electronic Data Interchange

-Composite of specialized standards that facilitates the flow of tasks such as accounting, shipping / receiving, and order and inventory tracking between business.

Bulletin Boards

-Includes Internet chat rooms, and sharing public domain software.

Internet Navigation Utilities

-Includes Gopher, WAIS, and search engines, e.g. Yahoo, Excite, and Alta Vista. Helps users locate resources and information on the Internet.

Financial Transaction Services

-They gather and sell information pertaining to investments and credit data to their subscribers.

Call Now : 800-519- 2267

Why Vibrant Boot camp

No Prestudy

Longest Duration Bootcamp

Chalk Talk Training

Highest Passing Rate

Bootcamp since 1997

Guaranteed Lowest Rate

Guaranteed Certification ...

Testimonials

If you're serious about getting certified, this is the place to go. Definitely worth their competitive price. Excellent instructors, making it possible for anyone to learn no matter what your level of experience or knowledge.

Michael Doty

MCITP MCSE CCNA CCNP Boot Camp

Application Layer